imprimante 3D delta 400MM/S
Updated 10 September 2026 · Live prices updated daily
Buy on Amazon.co.uk - £1000.00 →Affiliate link. Price live from the marketplace, not cached.
At a glance
What this printer gets right and wrong
- ✓ 300°C hot end - handles carbon-fibre nylons and PC, not just the easy stuff.
- ✓ 36.9 L build volume - room for helmets, large functional parts, bulk runs.
- ! Open frame - PLA and PETG only, realistically. Forget ABS or nylon done properly.
Head-to-head spec + price table against the WANHAO FRANCE imprimante 3D delta 400MM/S. Verified printers on this marketplace only.
At this price you're well past the sweet spot for a first printer. There's no shame in starting with something cheaper - you'll learn more on a 200-400 machine and have money left for filament.
Bedslinger with middling flow rate - you already have one of these. The whole point of upgrading is speed, rigidity, or print quality that your current machine can't hit. This doesn't clear that bar.
No active heated chamber or a hot end that tops out below 280°C means no reliable ABS, ASA, nylon or PC. Fine for a hobbyist, wrong tool for commercial work in engineering materials.
Verdicts are rule-driven from the spec sheet and current price (£1000). They don't capture firmware polish, support quality, or reliability - so treat them as a sanity check, not a final answer.
Live offers
Every live listing on the English-language Amazon marketplaces that I've matched to this printer. Cheapest first. Affiliate links.
- 🇬🇧 imprimante 3D delta 400MM/S (V400)Amazon.co.uk · New£1000.00View
Close alternatives - what $1000 gets you elsewhere
Think of this like the shopping-cart upsell: here's what a tenner more or less could buy you in roughly the same category. Same FDM tech, same marketplace, all prices live. Stretches are data-driven; they're not sponsored placements.
Save the money, similar specs on paper. You'd give up: 36.9 L vs 15.6 L build volume, 300°C hot end vs 290°C.
Get: 14.8 L more build volume (51.7 L) · 370°C hot end (was 300°C).
Get: a proper heated chamber, so ABS/ASA/nylon become realistic · CoreXY motion - faster, more rigid.
Frequently asked
What materials can the WANHAO FRANCE imprimante 3D delta 400MM/S print? +
At £1000 the WANHAO FRANCE imprimante 3D delta 400MM/S has the hot end for engineering materials (300°C) but no active chamber, so ABS and nylon will warp on anything larger than a phone case. Treat it as a PLA/PETG/TPU workhorse with headroom for the occasional small ABS part.
How fast is the WANHAO FRANCE imprimante 3D delta 400MM/S? +
Advertised at 600 mm/s, but that is motion-system capability, not what the hot end can sustain. Expect real-world prints at 80-150 mm/s without quality collapse.
How big can I print on the WANHAO FRANCE imprimante 3D delta 400MM/S? +
300×300×410 mm (36.9 L). Big enough for helmets in one piece, full-scale cosplay props, or multiple medium parts in one run. Reliability starts mattering at this scale - a failed 20-hour print stings.
Does the WANHAO FRANCE imprimante 3D delta 400MM/S have auto-levelling? +
Yes - Auto Leveling auto-levelling probe. Not quite as clean as load-cell or LiDAR, but reliable once calibrated and a world better than manual paper-under-the-nozzle.
Is the WANHAO FRANCE imprimante 3D delta 400MM/S worth £1000? +
£1000+ is prosumer/workshop money. Diminishing returns on print quality versus a $700-1000 machine; real returns on long-term reliability, support contracts and replacement parts. Worth it if the printer makes you money, overkill if it is a weekend hobby.
