Impresora 3D con Nivelación de Placa de
Updated 26 September 2026 · Live prices updated daily
Buy on Amazon.es - €685.29 →Affiliate link. Price live from the marketplace, not cached.
At a glance
What this printer gets right and wrong
- ✓ 36.0 L build volume - room for helmets, large functional parts, bulk runs.
- ! Nothing stands out as a clear weakness on the spec sheet - but spec sheets never capture firmware polish, customer support or long-term reliability. Read owner reports before committing.
Head-to-head spec + price table against the MasYosh Impresora 3D con Nivelación de Placa de. Verified printers on this marketplace only.
At this price you're well past the sweet spot for a first printer. There's no shame in starting with something cheaper - you'll learn more on a 200-400 machine and have money left for filament.
Bedslinger with middling flow rate - you already have one of these. The whole point of upgrading is speed, rigidity, or print quality that your current machine can't hit. This doesn't clear that bar.
No active heated chamber or a hot end that tops out below 280°C means no reliable ABS, ASA, nylon or PC. Fine for a hobbyist, wrong tool for commercial work in engineering materials.
Verdicts are rule-driven from the spec sheet and current price (€685). They don't capture firmware polish, support quality, or reliability - so treat them as a sanity check, not a final answer.
Live offers
Every live listing on the English-language Amazon marketplaces that I've matched to this printer. Cheapest first. Affiliate links.
- 🇪🇸 MasYosh Impresora 3D con Nivelación de Placa de Superficie de Construcción Extraíble FDM 300X300X400 MmAmazon.es · New€685.29View
Close alternatives - what $685 gets you elsewhere
Think of this like the shopping-cart upsell: here's what a tenner more or less could buy you in roughly the same category. Same FDM tech, same marketplace, all prices live. Stretches are data-driven; they're not sponsored placements.
Save the money, similar specs on paper. You'd give up: 36.0 L vs 18.7 L build volume.
Get: 6.9 L more build volume (42.9 L) · 350°C hot end (was —°C).
Get: 370°C hot end (was —°C) · a proper heated chamber, so ABS/ASA/nylon become realistic.
Frequently asked
What materials can the MasYosh Impresora 3D con Nivelación de Placa de print? +
At €685 the MasYosh Impresora 3D con Nivelación de Placa de realistically prints PLA and TPU. The listed°C hot end is too tight for PETG with confidence and rules out ABS/nylon entirely.
How fast is the MasYosh Impresora 3D con Nivelación de Placa de? +
Advertised at 150 mm/s, but that is motion-system capability, not what the hot end can sustain. Expect real-world prints at 80-150 mm/s without quality collapse.
How big can I print on the MasYosh Impresora 3D con Nivelación de Placa de? +
300×300×400 mm (36.0 L). Big enough for helmets in one piece, full-scale cosplay props, or multiple medium parts in one run. Reliability starts mattering at this scale - a failed 20-hour print stings.
Does the MasYosh Impresora 3D con Nivelación de Placa de have auto-levelling? +
Yes - Matrix leveling (25 points) auto-levelling probe. Not quite as clean as load-cell or LiDAR, but reliable once calibrated and a world better than manual paper-under-the-nozzle.
Is the MasYosh Impresora 3D con Nivelación de Placa de worth €685? +
€685 is serious hobbyist territory. For the MasYosh Impresora 3D con Nivelación de Placa de to justify this over a $500 machine it needs to deliver genuine speed (volumetric flow), reliability at speed, or access to engineering materials. Check the spec table above against those three.
