Best 3D printers with remote monitoring

Updated 26 September 2026 · Live prices updated daily

Wi-Fi plus an integrated camera so you can watch the print from the sofa, from the office, or from bed at 2 AM when you hear the part-cooling fan change pitch.

#1

ANYCUBIC

Kobra S1 Max Stampante 3D

€700 CoreXY · heated chamber · 42.9 L · 350°C · LeviQ 3.0
#2

QIDI

Plus5 Stampanti 3D

€749 CoreXY · heated chamber · 30.7 L · 370°C · Loadcell
#3

QIDI

Q2C Stampanti 3D

€359 CoreXY · 18.9 L · 370°C · Loadcell Sensor Integrated int
#4

Creality

K2 Plus Stampante 3D

€1349 CoreXY · 42.9 L · 350°C · Strain gauge
#5

Sovol

SV08 Core XY - Voron 2.4 Open Source Stamp

€549 CoreXY · 42.4 L · 300°C · QGL
#6

ANYCUBIC

Kobra 4 Stampante 3D Con ACE 2 Pro

€460 Bedslinger · 17.6 L · 300°C · LeviQ 3.0
#7

ANYCUBIC

Kobra S1 Stampante 3D

€440 CoreXY · 15.6 L · 320°C · LeviQ3.0
#8

BAMBULAB

Bambu Lab Stampante 3D - P1S

€500 CoreXY · 16.8 L · 300°C · Strain gauge
#9

Creality

K1 Stampante 3D 600 mm/s ad alta velocità

€460 CoreXY · 12.1 L · 300°C · Self Check | Auto Leveling
#10

BAMBULAB

Bambu Lab A1 Mini Stampante 3D+Luce LED

€212 CoreXZ · 5.8 L · 300°C · Strain gauge

Matt's take

Remote monitoring sounds like a gimmick until a print fails at hour eight and you were out. A camera plus pause-on-spaghetti detection turns a ruined weekend into a re-sliced Monday. Two caveats: most first-party cameras are 720p and lag by 2-4 seconds, which is fine for status checks and bad for artistic recording; and cloud features on Bambu, Creality and Anycubic require you to own an account with them - consider what that means for your data. Local-only Octoprint-flavoured options exist but take more setup.

Frequently asked

Do I really need a camera on my 3D printer? +

For the first month, no. After your first failed print that you did not catch until hour eight of twelve, yes. A camera plus "stop if the AI spots a failure" turns most spaghetti into a wasted hour, not a wasted weekend.

How good is Bambu Lab's AI failure detection? +

It catches the obvious failures (classic bed detachment spaghetti) reliably. It misses subtle ones like one wall of a thin-walled print delaminating. Worth having; not a replacement for checking in periodically.

Can I self-host printer monitoring without the cloud? +

Yes - Klipper + Mainsail or Octoprint on a Raspberry Pi with a USB webcam is the standard DIY route. About £80 of hardware plus an afternoon of setup. Gives you full control and no vendor account.

Other shortlists

for ABS, ASA and nylon large-format 3D printers CoreXY 3D printers for beginners Quietest 3D printers - flat and studio friendly multi-colour and multi-material 3D printers for tabletop miniatures for schools and classrooms Fastest 3D printers (by real volumetric flow) with high-temp heated beds compact 3D printers (small desks, small spaces) for cosplay and props

Long readFDM vs resin 3D printingWhen each process wins, where each fails, and why most beginners should start with FDM.Read →Long readHow to pick your first 3D printerSpec by spec, what actually matters on a first printer and what the marketing hopes you will not question.Read →

Ranking is spec-driven. It favours printers that objectively have the capabilities this shortlist targets. Firmware, support quality and long-term reliability aren't on the spec sheet - read the full printer page and owner reports before committing.

Best 3D printers with remote monitoring

Matt's take

Frequently asked

Related reading