Da Vinci Jr Pro XE+ Harden Steel Nozzel Fully
Updated 9 September 2026 · Live prices updated daily
Buy on Amazon.com - $299.99 →Affiliate link. Price live from the marketplace, not cached.
At a glance
What this printer gets right and wrong
- ✓ Under $300 - low-risk way to get into 3D printing without regretting the spend.
- ! Bedslinger design - expect ringing artefacts on tall prints at speed.
Head-to-head spec + price table against the XYZprinting Da Vinci Jr Pro XE+ Harden Steel Nozzel Fully. Verified printers on this marketplace only.
Sensible first-printer territory: priced where you can afford to get it wrong, with auto-levelling so the first layer isn't a ritual. You'll outgrow it in 18 months, which is fine.
Bedslinger with middling flow rate - you already have one of these. The whole point of upgrading is speed, rigidity, or print quality that your current machine can't hit. This doesn't clear that bar.
No active heated chamber or a hot end that tops out below 280°C means no reliable ABS, ASA, nylon or PC. Fine for a hobbyist, wrong tool for commercial work in engineering materials.
Verdicts are rule-driven from the spec sheet and current price ($300). They don't capture firmware polish, support quality, or reliability - so treat them as a sanity check, not a final answer.
Live offers
Every live listing on the English-language Amazon marketplaces that I've matched to this printer. Cheapest first. Affiliate links.
- 🇺🇸 XYZPrinting Da Vinci Jr Pro XE+ 3D Printer Harden Steel Nozzel Fully Open Source 3D Printers Printing Size 6.9” x 6.9” x 6.9”Amazon.com · New$299.99View
Close alternatives - what $300 gets you elsewhere
Think of this like the shopping-cart upsell: here's what a tenner more or less could buy you in roughly the same category. Same FDM tech, same marketplace, all prices live. Stretches are data-driven; they're not sponsored placements.
Save the money, similar specs on paper. You'd give up: 5.4 L vs 1.7 L build volume.
Get: 5.3 L more build volume (10.6 L) · 300°C hot end (was 260°C).
Get: 50.6 L more build volume (56.0 L) · 300°C hot end (was 260°C).
Frequently asked
What materials can the XYZprinting Da Vinci Jr Pro XE+ Harden Steel Nozzel Fully print? +
At $300 the XYZprinting Da Vinci Jr Pro XE+ Harden Steel Nozzel Fully is a PLA, PETG, TPU machine. The 260°C hot end covers PETG with a small safety margin. ABS and nylon need an enclosure plus more heat - not this printer.
How fast is the XYZprinting Da Vinci Jr Pro XE+ Harden Steel Nozzel Fully? +
Advertised at 160 mm/s, but that is motion-system capability, not what the hot end can sustain. Expect real-world prints at 80-150 mm/s without quality collapse.
How big can I print on the XYZprinting Da Vinci Jr Pro XE+ Harden Steel Nozzel Fully? +
175×175×175 mm (5.4 L). Mainstream bed size - fits 90 % of what people actually print. Cosplay helmets will need to be sliced into sections.
Does the XYZprinting Da Vinci Jr Pro XE+ Harden Steel Nozzel Fully have auto-levelling? +
Yes - Auto auto-levelling probe. Not quite as clean as load-cell or LiDAR, but reliable once calibrated and a world better than manual paper-under-the-nozzle.
Is the XYZprinting Da Vinci Jr Pro XE+ Harden Steel Nozzel Fully worth $300? +
$300 is the sweet spot tier. The XYZprinting Da Vinci Jr Pro XE+ Harden Steel Nozzel Fully competes directly with the current Bambu A1, Creality K1 and Prusa Mini generation. Hardware-per-pound is tight here - the differentiator is usually software polish and ecosystem.
