Kobra S1 Impresora 3D
Updated 26 September 2026 · Live prices updated daily
Buy on Amazon.es - €336.00 →Affiliate link. Price live from the marketplace, not cached.
At a glance
What this printer gets right and wrong
Nothing jumps out on the spec sheet as a standout feature at this price.
- ! Bedslinger design - expect ringing artefacts on tall prints at speed.
- ! Open frame - PLA and PETG only, realistically. Forget ABS or nylon done properly.
Head-to-head spec + price table against the ANYCUBIC Kobra S1 Impresora 3D. Verified printers on this marketplace only.
Sensible first-printer territory: priced where you can afford to get it wrong, with auto-levelling so the first layer isn't a ritual. You'll outgrow it in 18 months, which is fine.
Bedslinger with middling flow rate - you already have one of these. The whole point of upgrading is speed, rigidity, or print quality that your current machine can't hit. This doesn't clear that bar.
No active heated chamber or a hot end that tops out below 280°C means no reliable ABS, ASA, nylon or PC. Fine for a hobbyist, wrong tool for commercial work in engineering materials.
Verdicts are rule-driven from the spec sheet and current price (€336). They don't capture firmware polish, support quality, or reliability - so treat them as a sanity check, not a final answer.
Live offers
Every live listing on the English-language Amazon marketplaces that I've matched to this printer. Cheapest first. Affiliate links.
- 🇪🇸 ANYCUBIC Kobra S1 Impresora 3D,600mm/s Impresoras 3D Multicolor LeviQ 3.0Amazon.es · New€336.00View
Close alternatives - what €336 gets you elsewhere
Think of this like the shopping-cart upsell: here's what a tenner more or less could buy you in roughly the same category. Same FDM tech, same marketplace, all prices live. Stretches are data-driven; they're not sponsored placements.
Save the money, same build volume at 17.6 L. You'd give up: nothing obvious on the spec sheet.
Get: 6.8 L more build volume (18.9 L) · 370°C hot end (was 260°C).
Get: 300°C hot end (was 260°C) · CoreXY motion - faster, more rigid.
Frequently asked
What materials can the ANYCUBIC Kobra S1 Impresora 3D print? +
At €336 the ANYCUBIC Kobra S1 Impresora 3D is a PLA, PETG, TPU machine. The 260°C hot end covers PETG with a small safety margin. ABS and nylon need an enclosure plus more heat - not this printer.
How fast is the ANYCUBIC Kobra S1 Impresora 3D? +
Advertised at 180 mm/s, but that is motion-system capability, not what the hot end can sustain. Expect real-world prints at 80-150 mm/s without quality collapse.
How big can I print on the ANYCUBIC Kobra S1 Impresora 3D? +
220×220×250 mm (12.1 L). Comfortable for medium props, functional parts up to ~25 cm, and batch printing. One of the most-used working sizes in hobby 3D printing.
Does the ANYCUBIC Kobra S1 Impresora 3D have auto-levelling? +
Yes - Automatic auto-levelling probe. Not quite as clean as load-cell or LiDAR, but reliable once calibrated and a world better than manual paper-under-the-nozzle.
Is the ANYCUBIC Kobra S1 Impresora 3D worth €336? +
€336 is the sweet spot tier. The ANYCUBIC Kobra S1 Impresora 3D competes directly with the current Bambu A1, Creality K1 and Prusa Mini generation. Hardware-per-pound is tight here - the differentiator is usually software polish and ecosystem.
