ANYCUBIC Kobra 3
Updated 8 September 2026 · Live prices on every page load from Amazon US + UK
Buy on Amazon.com - $782.68 →Affiliate link. Price live from the marketplace, not cached.
At a glance
What this printer gets right and wrong
- ✓ 300°C hot end - handles carbon-fibre nylons and PC, not just the easy stuff.
- ! Bedslinger design - expect ringing artefacts on tall prints at speed.
- ! Open frame - PLA and PETG only, realistically. Forget ABS or nylon done properly.
Head-to-head spec + price table against the Microcenter ANYCUBIC Kobra 3. Verified printers on this marketplace only.
At this price you're well past the sweet spot for a first printer. There's no shame in starting with something cheaper - you'll learn more on a 200-400 machine and have money left for filament.
Bedslinger with middling flow rate - you already have one of these. The whole point of upgrading is speed, rigidity, or print quality that your current machine can't hit. This doesn't clear that bar.
No active heated chamber or a hot end that tops out below 280°C means no reliable ABS, ASA, nylon or PC. Fine for a hobbyist, wrong tool for commercial work in engineering materials.
Verdicts are rule-driven from the spec sheet and current price ($783). They don't capture firmware polish, support quality, or reliability - so treat them as a sanity check, not a final answer.
Live offers
Every live listing on the English-language Amazon marketplaces that I've matched to this printer. Cheapest first. Affiliate links.
- 🇺🇸 ANYCUBIC Kobra 3 Combo 3D PrinterAmazon.com · New$782.68View
Close alternatives - what $783 gets you elsewhere
Think of this like the shopping-cart upsell: here's what a tenner more or less could buy you in roughly the same category. Same FDM tech, same marketplace, all prices live. Stretches are data-driven; they're not sponsored placements.
Save the money, same build volume at 49.0 L. You'd give up: nothing obvious on the spec sheet.
Get: 320°C hot end (was 300°C) · a proper heated chamber, so ABS/ASA/nylon become realistic.
Get: 26.6 L more build volume (42.9 L) · 350°C hot end (was 300°C).
Frequently asked
What materials can the Microcenter ANYCUBIC Kobra 3 print? +
At $783 the Microcenter ANYCUBIC Kobra 3 has the hot end for engineering materials (300°C) but no active chamber, so ABS and nylon will warp on anything larger than a phone case. Treat it as a PLA/PETG/TPU workhorse with headroom for the occasional small ABS part.
How fast is the Microcenter ANYCUBIC Kobra 3? +
Advertised at 600 mm/s, but that is motion-system capability, not what the hot end can sustain. Expect real-world prints at 80-150 mm/s without quality collapse.
How big can I print on the Microcenter ANYCUBIC Kobra 3? +
250×250×260 mm (16.3 L). Comfortable for medium props, functional parts up to ~25 cm, and batch printing. One of the most-used working sizes in hobby 3D printing.
Does the Microcenter ANYCUBIC Kobra 3 have auto-levelling? +
Yes - LeviQ 3.0 auto-levelling probe. Not quite as clean as load-cell or LiDAR, but reliable once calibrated and a world better than manual paper-under-the-nozzle.
Is the Microcenter ANYCUBIC Kobra 3 worth $783? +
$783 is serious hobbyist territory. For the Microcenter ANYCUBIC Kobra 3 to justify this over a $500 machine it needs to deliver genuine speed (volumetric flow), reliability at speed, or access to engineering materials. Check the spec table above against those three.
