Kobra 2 Plus 3D-Drucker
Updated 16 October 2026 · Live prices updated daily
Buy on Amazon.de - €349.00 →Affiliate link. Price live from the marketplace, not cached.
At a glance
What this printer gets right and wrong
- ✓ 41.0 L build volume - room for helmets, large functional parts, bulk runs.
- ! Bedslinger design - expect ringing artefacts on tall prints at speed.
- ! Open frame - PLA and PETG only, realistically. Forget ABS or nylon done properly.
Head-to-head spec + price table against the ANYCUBIC Kobra 2 Plus 3D-Drucker. Verified printers on this marketplace only.
Sensible first-printer territory: priced where you can afford to get it wrong, with auto-levelling so the first layer isn't a ritual. You'll outgrow it in 18 months, which is fine.
Bedslinger with middling flow rate - you already have one of these. The whole point of upgrading is speed, rigidity, or print quality that your current machine can't hit. This doesn't clear that bar.
No active heated chamber or a hot end that tops out below 280°C means no reliable ABS, ASA, nylon or PC. Fine for a hobbyist, wrong tool for commercial work in engineering materials.
Verdicts are rule-driven from the spec sheet and current price (€349). They don't capture firmware polish, support quality, or reliability - so treat them as a sanity check, not a final answer.
Live offers
Every live listing on the English-language Amazon marketplaces that I've matched to this printer. Cheapest first. Affiliate links.
- 🇩🇪 Anycubic Kobra 2 Plus 3D-Drucker, Große Druckgröße 320 * 320 * 400mm, 500mm/s Hochgeschwindigkeitsdruck, 3D Printer mit Auto LevelingAmazon.de · New€349.00View
Close alternatives - what €349 gets you elsewhere
Think of this like the shopping-cart upsell: here's what a tenner more or less could buy you in roughly the same category. Same FDM tech, same marketplace, all prices live. Stretches are data-driven; they're not sponsored placements.
Save the money, similar specs on paper. You'd give up: 41.0 L vs 29.7 L build volume.
Get: 300°C hot end (was 260°C) · CoreXY motion - faster, more rigid.
Get: 47.2 L more build volume (88.2 L) · 300°C hot end (was 260°C).
Frequently asked
What materials can the ANYCUBIC Kobra 2 Plus 3D-Drucker print? +
At €349 the ANYCUBIC Kobra 2 Plus 3D-Drucker is a PLA, PETG, TPU machine. The 260°C hot end covers PETG with a small safety margin. ABS and nylon need an enclosure plus more heat - not this printer.
How fast is the ANYCUBIC Kobra 2 Plus 3D-Drucker? +
Advertised at 500 mm/s, but that is motion-system capability, not what the hot end can sustain. Expect real-world prints at 80-150 mm/s without quality collapse.
How big can I print on the ANYCUBIC Kobra 2 Plus 3D-Drucker? +
320×320×400 mm (41.0 L). Big enough for helmets in one piece, full-scale cosplay props, or multiple medium parts in one run. Reliability starts mattering at this scale - a failed 20-hour print stings.
Does the ANYCUBIC Kobra 2 Plus 3D-Drucker have auto-levelling? +
Yes - LeviQ 2.0 auto-levelling probe. Not quite as clean as load-cell or LiDAR, but reliable once calibrated and a world better than manual paper-under-the-nozzle.
Is the ANYCUBIC Kobra 2 Plus 3D-Drucker worth €349? +
€349 is the sweet spot tier. The ANYCUBIC Kobra 2 Plus 3D-Drucker competes directly with the current Bambu A1, Creality K1 and Prusa Mini generation. Hardware-per-pound is tight here - the differentiator is usually software polish and ecosystem.
